logobossparts

2 SAFETY PRECAUTIONSCAUTIONRISK OF ELECTRIC SHOCKDO NOT OPENCAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. The analog video to HDMI conversion function 15Connecting equipment with HDMI terminalsTo convert analog video signals to HDMI signals 16Connecting a TV tuner 16Connecting a DBS tuner16Connecting the external inputs (EXT. ENGLISHGetting StartedAdvanced Setup – Part 1System setup items and default values 43 45 Navigating through the System Setup Menu 46About the display46Audio Input SetupSetting the Digital In Assignment47 Setting the EXT. Getting StartedOperating the remote control unitOperating DENON audio components62Setting the preset memory function 62Operating a component stored in the preset memory 63Setting the learning function64Using the system call function 64Registering64Operating64Setting the punch through function 65Resetting the remote control unitResetting the learning function 65Resetting the punch through setting 65Additional Information66 68Troubleshooting 69Specifications 70List of preset codes End of this manual. Getting StartedAccessoriesCheck that the following parts are attached in addition to the main unit:q Operating instructions.1w Service station list.1e Power supply cord (Approx. 1.5 m).1r Remote control unit (RC-1030).1t R6P/AA batteries.3y AM loop antenna.1u FM indoor antenna.1i Setup microphone (DM-S205) (Approx.

1. Denon Rc-1216 Manual

6 m).1ertyuiBefore usingPay attention to the following before using this unit:. Moving the unitTo prevent short-circuits or damaged wires in the connection cables, always unplug the power supply cord and disconnect the connection cables between all other audio components when moving the unit.

Before turning the power switch onCheck once again that all connections are correct and that there are not problems with the connection cables. Always set the power switch to the standby position before connecting and disconnecting connection cables.

Store these instructions in a safe place.After reading, store this instructions along with the warranty card in a safe place. Whenever the power switch is in the STANDBY state, the unit is still connected to AC line voltage.Please be sure to turn off the power switch or unplug the cord when you leave home for, say, a vacation. Note that the illustrations in these instructions may differ from the actual unit for explanation purposes. Cautions on installationNote:For heat dispersal, do not install this unit in a confined space such as a bookcase or similar enclosure.NoteWallAbout the remote control unitIn addition to controlling the AVR-2807, the attached remote control unit (RC-1030) can also be used to control the following products:q DENON component productsw Component products other than DENON:. Set using the preset memory function ( page 62, 63). Set using the learning function ( page 64).Inserting the batteriesq Remove the remote control w Set 3 R6P/AA batteries in unit’s rear cover.

The battery compartment inthe indicated direction.e Put the rear cover back on.3. ENGLISHGetting StartedNotes on batteries:.

Replace the batteries with new ones if the set does not operate even when the remote control unit is operated nearby the unit. Q Power ON/STANDBY button (10)w Power indicator(10)e Power switch(10)r Headphones jack (PHONES) (25)t V.AUX INPUT terminals (17)y SETUP MIC jack (9)u USER MODE buttons(38)i MASTER VOLUME control knob (23)o Master volume indicator!0Display!1 MultEQ XT indicator(24)!2 NIGHT indicator (38)!3 Remote control sensor(3)!4 FUNCTION knob(23)!5 SOURCE button (23)!6 TUNING PRESET button (36)!7ZONE2/REC SELECT button (41, 42)!8 VIDEO SELECT button(38). !9 NIGHT button (38)@0 PURE DIRECT button(25)@1 DIRECT/STEREO button(25)@2 STANDARD button (26)@3 7CH STEREO button (33)@4 DSP SIMULATION button (33)@5CH SELECT/ENTER button (10, 34)@6SURROUND PARAMETER button (26)@7 TONE DEFEAT button(34)@8 DIMMER button (24)@9 STATUS button (24)#0 ROOM EQ button(24)#1 SURROUND BACK button (26)#2Cursor ( D, H, F, G) buttons (10)#3 SYSTEM SETUP button (10)#4 EXT. IN button(23)#5 ANALOG button(23)#6 INPUT MODE button (23). O AL24 indicatorThis lights when the following mode is selected while inputting digital (PCM) signals.PURE DIRECT / DIRECT / STEREO / MULTI CH PURE DIRECT /MULTI CH DIRECT / MULTI CH IN!0Input mode indicator!1RDS indicatorThis lights when an RDS broadcast has been received.!2AUTO indicatorThis lights when the broadcast station is selected in the AUTO tuning mode.!3TUNED indicatorThis lights when an FM/AM broadcast has been received.!4STEREO indicatorThis lights when an FM stereo broadcast has been received. ENGLISHEasy Setup Procedure.steps necessary to configure the AVR-2807 according to yourand the source equipment and loudspeakers you are using.see pages 56 59.Easy to setup flowPlacing the speakers.Auto setup flowConnecting a microphone.Connecting thespeakers.Preliminary measurement.Connecting a monitorand a DVD player.Starting the AutoMeasurement of the speakersSetup.in the listening position.Playing a DVD withsurround sound.Speaker measurement checkand storage in memory. Easy Setup ProcedureSpeaker connectionsConnect the speaker terminals with the speakers making sure that like polarities are matched ( with ).NOTE:When making connections, take care that none of the individual conductors of the speaker cable come in contact with adjacent terminals, with other speaker cable conductors, or with the rear panel and screws.NEVER touch the speaker terminals when the power is on.

Doing so could result in electric shocks.Connecting the speaker cables1. Loosen by turning counterclockwise.Either tightly twist or terminate the core wires.2.

Insert the cable.3. Tighten by turning clockwise. 2 Speaker impedanceSpeakerImpedanceFront A, B6 16 Ω/ohmsFront A+B8 16 Ω/ohmsCenter6 16 Ω/ohmsSurroundSurround backNote on speaker impedanceWhen using speakers with an impedance below the designated value (for example 4 Ω /ohms), playing for long periods of time with the volume high could cause the temperature to rise, activating the protection circuit.When the protection circuit is activated, the output to the speakers is cut off and the power indicator blinks. If this happens, unplug the power cord, wait for the set to cool off and improve ventilation around the unit. Also check the wiring of the input cables and the speaker cables.

After doing this, plug the power cord back in and turn the unit’s power back on.If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the unit, switch off the power and contact a DENON service center. ENGLISHEasy Setup Procedure2 Connections. With the AVR-2807, up to 10 speakers can be connected for surround playback. When making connections, also refer to the operating instructions of the other components.Front speakerFront speakerSubwooferCenter speaker(A)(B)Connectionterminal forsubwooferwith built-in(L)(R)(L)(R)amplifier. ENGLISHEasy Setup ProcedureConnecting a DVD player and monitor.

To connect the video output from the DVD player to the AVR-2807, you only need to choose one connection type. For more information about the video up conversion function ( page 14, 15). To connect the digital audio output from the DVD player, you can choose from either the coaxial or optical connections. If you choose to use the optical connection, it needs to be assigned.

For more information about Digital Input Assignment ( page 47).DVD playerHCOMPONENT VIDEO OUTYP BP RIHDMIOUTFVIDEOOUTGS-VIDEOOUTAAUDIO OUTLLLRRRDOPTICALOUTCCOAXIALOUTAudio signal flow is shown with white arrows, video signal flow is shown with gray arrows.AVR-2807 is equipped with another set of input terminals for a non-DVD video disc player as laser disc, VCD/SVCD, or future high definition disc player). The above connectionfor DVD also apply to the VDP input.

Easy Setup Procedure. For best picture quality (especially with progressive DVD and other high definition sources), choose the component video or HDMI connection to your monitor. S-Video and composite video outputs are also provided if your monitor does not have component video inputs.MonitorHCOMPONENT VIDEO INYP BP RGS-VIDEOINFVIDEOINIHDMIINAVR-2807 is equipped with HDMI terminals, so it can be connected to a DVD player or using an HDMI cable.component video input and/or output terminals may be labelled differently on some monitors components. Check the owner’s manuals for other components for further information.COMPONENT MONITOR OUT-1 and the COMPONENT MONITOR OUT-2 can be used.signals are only output from the HDMI monitor out terminal when audio signals are input HDMI input terminal.connecting the AVR-2807 and DVD player using an HDMI cable, also connect the AVRand monitor using an HDMI cable ( page 19). The AVR-2807’s auto setup and room equalizer functions use the attached microphone to measure the acoustic properties in the room and automatically make the optimum settings. The optimum listening environment at all listening positions in the home theater is achieved so multiple listeners can enjoy listening at the same time.As shown in Example q, as you make the measurements, move the microphone successively to the different positions in which the members of the family sit within the listening area surrounded by the speakers.

ENGLISHEasy Setup Procedurew Before performing the Auto Setup procedure1 Turn on your subwoofer.Set the volume to halfway and set the crossover frequency to the maximum or Low pass filter off if your subwoofer can adjust the output volume and the crossover frequency.Some subwoofers have a standby mode. Be sure to turn this function off before performing the Auto Setup procedure.2 Turn on your monitor.3 Press.¢ ON:The power indicator lights red.£ OFF:The power turns off and the indicator is off.4 Press or ON. The power indicator blinks green and the power turns on.

Easy Setup Procedurer Assigning power amplifiersThe surround back output can be assigned to the “Front” or “ZONE2” output.Press D H to select “Power Amp Assign”, then press F G to set.Surround Back:Assign to use as surround back speaker.Front A, Front B:Assign to use the “Front A” (or “Front B”) speakers with biamp connections.ZONE2:Assign to use as “ZONE2” speakers.When assigned to “Front”, skip the surround back channel measurement.During the auto setup procedure, test tones are not output to “ZONE2”. Cautions during measurements:.

Loud test tones are output during the measurements. Be careful for example when small children are nearby. Proper measurements may not be possible if there are obstacles between the speaker and the setup microphone. During the measurements, do not stand between or near the speakers and setup microphone. To avoid influencing the measurements, turn off the power of air-conditioners or any other equipment producing sound in the room. Perform the measurements with the room as quiet as possible. Measurement is cancelled when VOLUME is operated while the Auto Setup is performed.u Speaker measurementsWith these measurements, the “Speaker Configuration”, “Distance”, “Channel Level”, “Crossover Frequency” and “Room EQ” settings are analyzed automatically.

The main listening position is measured first, so leave the microphone where it is.1 Press D H to select “OK Start”, then press F. Measurements for the first point start.2 Move the microphone to the second point and press F. Measurements for the second point start.Once the measurements are finished, the results of the measurements for the second point are displayed.3 Perform step 2 repeatedly.Measurements can be ended when there are 6 or less measurement locations; however, to obtain better results, measurements at 6 locations is recommended.11. ENGLISHEasy Setup Procedure4 Press D H to select “Calculate”, then press F.

The speaker is analyzed.Once the calculations are completed, a screen for confirming the results of the measurements appears.The amount of time required for the analysis depends on the number of speakers and the number of measuring points. The greater the number of speakers and measuring points, the longer the time required.12h4h h(After completion of measurement for first point)NOTE:. Do not change the speaker connections or subwoofer volume after making the measurements.

ENGLISHEasy Setup Procedurei Checking and storing the measurement resultsThe measurement results displayed at “u Speaker measurements” can be checked and stored in the memory.1 Press D H to select the item, then press ENTER.Press ENTER to switch to the second screen.2 After set. Checking, press ENTER, then press D H toStore:All the settings are stored in the memory.Cancel:Cancel the auto setup settings.3 When “Store” is selected: Press F. After the data is stored, the “Auto Setup / Room EQ” screen appears automatically.12measurements have been made using the measurement speakers with a built-in filter such as subwoofers be set with a value that differs from the physical distanceof the internal electrical delay.NOTE:. Do not turn off the power while the data is being stored.

Easy Setup ProcedureError messagesAn error message is displayed if the measurements could not be completed automatically due to the speaker layout, the measuring environment, etc. ENGLISHConnecting Other SourcesThe video conversion function.

Even if the formats of the video signals from the various players differ, the different formats can be converted and the signals output to the monitor from a single video output terminal. We recommend outputting with the format offering the highest quality video signals possible.

With analog video signal connections, generally quality is higher in the order shown below.The flow of the video signals.(HDMI terminal)(HDMIterminal)(Component Video(Component Videoterminals)terminals)(S-Video terminal)(S-Video terminal)(Video terminal)(Video terminal)This unit’s inputThis unit’s outputterminalsterminals: only MAIN ZONE 480i/576i. Connecting Other SourcesVideo convertS-VIDEOInput signalsMONITOR OUTMONITOR OUTHDMICOMPONENTS-VIDEOVIDEOHDMICOMPONENTS-VIDEOVIDEO–EEEEEEEE–EEECEEEVIDEO–EECEEES-VIDEOEUsedEECCEES-VIDEOVIDEO2Not usedEECCEE–VIDEO–ECEEECOMPONENTEE–ECECECOMPONENT1EVIDEO–ECCEECOMPONENT2S-VIDEOEUsedECCCECOMPONENT2S-VIDEOVIDEO2OFFNot usedECCCECOMPONENT1–VIDEO–CEEEHDMIEEE–CEECHDMIEEVIDEO–CECEHDMIES-VIDEOEUsedCECCHDMIES-VIDEOVIDEO2Not usedCECCHDMIE–VIDEO–CCEEHDMICOMPONENTEE–CCECHDMICOMPONENT1EVIDEO–CCCEHDMICOMPONENT2S-VIDEOEUsedCCCCHDMICOMPONENT2S-VIDEOVIDEO2Not usedCCCCHDMICOMPONENT1–VIDEO. Connecting Other SourcesConnecting equipment with HDMI terminalsTo convert analog video signals to HDMI signals. The AVR-2807 is equipped with a function for converting analog video signals into HDMI signals. You can do this by either a component or a video or a S-Video connection. Audio signals are not output from the HDMI monitor output terminal, so also make analog or digital audio connections. To play sound using digital audio connections, assign the digital terminal (coaxial or optical) at “Setting the Digital In Assignment” ( page 47).MonitorIHDMIINDVD playerHCOMPONENT VIDEO OUTYP BP RFVIDEOOUTGS-VIDEOOUTDOPTICALOUTCCOAXIALOUTAAUDIO OUTLLLRRR“OFF” is set at “i/p Convert” under “Setting the HDMI Out Setup”, use a monitor with input resolutions of 480i/576i.monitor is not equipped with an HDMI terminal, connect the AVR-2807 to the monitor the component video, S-Video, or composite video terminals.

Connecting Other SourcesConnecting a TV tuner. For best picture quality choose the component video connection to your TV tuner. S-Video and composite video outputs are also provided if your TV tuner does not have component video inputs. To connect the digital audio output from the TV tuner, you can choose from either the coaxial or the optical connections. If you choose to use the coaxial or the optical connection, it needs to be assigned. For more information about Digital Input Assignment ( page 47).TV tunerHCOMPONENT VIDEO OUTYP BP RGS-VIDEOOUTFVIDEOOUTAAUDIO OUTLLLRRRConnecting a DBS tuner. For best picture quality choose the component video connection to your DBS tuner.

S-Video and composite video outputs are also provided. To connect the digital audio output from the DBS tuner, you can choose from either the coaxial or optical connections. If you choose to use the coaxial connection, it needs to be assigned. For more information about Digital Input Assignment ( page 47).DBS / BS TunerHCOMPONENT VIDEO OUTYP BP RGS-VIDEOOUTFVIDEOOUTAAUDIO OUTLLLRRR. Connecting Other SourcesConnecting the external inputs (EXT. IN) terminals.

These terminals are for inputting multi-channel audio signals from an outboard decoder, or a component with a different type of multi-channel decoder, such as a DVD-Audio player, or a multichannel Super Audio CD player, or other future multi-channel sound format decoder. The video signal connection is the same as that for a DVD player ( page 8). For instructions on playback using the external input (EXT. IN) terminals ( page 23).DVD Audio-Video /Super Audio CD Player /External decoderA7.1ch AUDIO OUTLLFRONTLRRRBCENTERASURROUNDLLBACKLRRRASURROUNDLLLRRRBSUB-WOOFERdiscs on which special copyright protection measures have been taken, however, the digital may not be output from the DVD player. In this case, connect the DVD player’s analog -channel output to the AVR-2807’s EXT.

IN terminals for playback. Also refer to your DVDoperating instructions. Connecting a DVD recorder. For best picture quality choose the component video connection to your DVD recorder. S-Video and composite video outputs are also provided.

If you choose to use the component video connection, it needs to be assigned. Connecting a VCRThere are 2 sets of video deck (VCR) terminals, so 2 video decks can be connected for simultaneous recording or video copying.Video deckFVIDEOOUTGS-VIDEOOUTGS-VIDEOINFVIDEOINAAUDIO INLLLRRRAAUDIO OUTLLLRRRrecording to a VCR, it is necessary that the type of cable used with the playback source be the same type that is connected to the AVR-2807 VCR-1 (to 2) OUTPUT terminal.VCR-2 IN →S-Video cable: VCR-2 OUT →S-Video cableVCR-2 IN →Video cable: VCR-2 OUT →Video cableConnecting a tape deckTape deckAAUDIO OUTLLLRRRAAUDIO INLLLRRR. ENGLISHConnecting Other Sources2 Copyright Protection SystemTo play back the digital video and audio of DVDVideo and DVD-Audio through an HDMI/DVI-D connection, both the connected player and monitor are required to support a copyright protection system called HDCP (Highbandwidth Digital Content Protection System). HDCP is copy protection technology that comprises data encryption and authentication of the partner equipment.The AVR-2807 supports HDCP. Please see the user’s manual of your video display for more information about this. Digital monitor or DVD player only supports DVI-D, please obtain and use an HDMI-DVI cable or adaptor, available from your dealer.NOTE:. The audio signals on the multi/stereo area of Super Audio CDs are not output.

Connecting Other SourcesConnecting the power supply cordPower supply cord(Supplied)AC outlet (wall)AC 230 V, 50 HzAC OUTLET. SWITCHED (total capacity – 100 W (0.43 A))The power to the outlet is turned on andoff in conjunction with the POWER switchNOTE:on the main unit, and when the power is. Insert the plugs securely. Incompleteswitched between on and standby fromconnections will result in the generation ofthe remote control unit.noise.No power is supplied from this outlet. Only use the AC OUTLET for audiowhen this unit’s power is at standby. Never use it for hair driers,connect equipment whose total powermonitors or other electrical appliances.consumption exceeds 100 W (0.43 A). Playing the input source1 Use FUNCTION to select the input source you want to play.To select the input source when ZONE2/REC SELECT, VIDEO SELECT or TUNING PRESET is selected, press then operate.2 Press INPUT MODE.AUTO PCM DTSEXT.

IN ANALOGPress to select “ANALOG”, to select “EXT. IN”.AUTO (All auto mode):The type of input signal is detected and the AVR-2807’s surround mode is switched automatically.

Can be selected for sources for which the “Digital In Assign” ( page 47) is made.The mode switches automatically to DTS/ Dolby Digital/ PCM. The input switches to the analog input terminals is no digital signals are being input.PCM (exclusive PCM signal playback mode) and DTS (exclusive DTS signal playback mode):Played when the various signals are input. Noise may be generated when a mode different from the input signal is set.ANALOG (exclusive analog audio signal playback mode) and EXT.

IN (External decoder input terminal selection mode):The signals input to the various input terminals are played.To lower the subwoofer channel level in the EXT. IN mode, press SURROUND PARAMETER and select “SW. ATT”.For some players the playback level of the SW channel may seen strong. If so, set to “ON”.3 Start playback on the selected component.For operating instructions, refer to the component’s manual.23.

4 Use VOLUME to adjust the volume. The volume level is displayed on the master volume level display.The volume can be adjusted between the range of –80 0 18 dB. Depending on the channel level settings and the different surround mode settings and when in the down-mix mode, it may not be possible to adjust the volume to 18 dB.

Canceling the EXT. IN mode:Press INPUT MODE, or to switch to the desired input mode. To use the EXT.

IN mode together with a picture, select the input source to which the video signal is connected first, then set the input mode. The “DIG.” indicator lights when digital signals are being inputproperly. If the “DIG.” indicator does not light, check whether the “Digital In Assign” ( page 47) and connections are correct.NOTE:. When the input mode is set to the external input (EXT. IN), the surround mode cannot be set. In play modes other than the external input mode, the signals connected to these terminals cannot be played.Cautions when playing DTS sources:.

For DTS sources, be sure to connect the device to the digital input terminal and set “AUTO” or “DTS” for the input source. Noise will be generated if you play in the ANALOG or PCM mode. When playing DTS signals in the “AUTO” mode, noise may be generated when you first start playing and during searching. If so, play in the “DTS” mode. Selecting the room equalizer modeThe room equalizer function offers 3 correction curves: “Audyssey”, “Front” and “Flat”. Basic OperationSwitching the front speakersPress SPEAKER.FRONT A FRONT BFRONT A+BChecking the currently playing program source, etc.2 On screen displayPress ON SCREEN.

The current program source and various settings are displayed on the monitor screen.2 Front panel displayPress. The current program source and various settings are indicated on the display.Switching the brightness of the displayPress.The brightness of the display can be adjusted in 3 steps.

The display can also be turned off. Basic OperationUsing the surround modesTypes of surround modes and their featuresThe AVR-2807 is equipped with many surround modes.

Recorded in stereo recorded in monauralPURE DIRECTUse this mode to play analog input music sources with extremely high quality.DIRECT / STEREO. Effective for achieving pure playback.If there is no need for tone control or distribution of the low frequencies in function of the speaker configuration, select the DIRECT mode to achieve the best sound quality.DENON Original Surround Modes ( page 32, 33). Select these for 7.1-channel playback with sources recorded in stereo or monaural. The effects are different for each of the surround modes. ENGLISHBasic OperationSelecting the play mode(PURE DIRECT / DIRECT / STEREO)The AVR-2807 is equipped with 3 2-channel playback modes exclusively for music. Select the mode to suit your tastes.2 PURE DIRECT modeThis mode reproduces the sound with extremely high quality. The audio signals do not pass through the tone circuits, etc., and the display and surrounding circuits that could affect the audio signals are turned “OFF”.Press PURE DIRECT.2 DIRECT modeThis mode is for playing with high quality sound.

The audio signals are transmitted directly, without passing through the tone circuits, etc.Press DIRECT/STEREO to select “DIRECT”.DIRECT STEREOWhen press SURROUND PARAMETER:The subwoofer output can be controlled directly.2 STEREO modeUse this mode to adjust the tone and achieve the desired sound.Press DIRECT/STEREO to select “STEREO”.system setup function cannot be used when the PURE mode is set. To use the system setup function, cancelPURE DIRECT mode.HDMI input terminal is selected, video outputs are output PURE DIRECT mode.channel level and surround parameters in the PURE mode are the same as in the DIRECT mode. Selecting the Dolby Digital and DTS Surround mode (only with digital input)1 Select an input source for which digital (COAXIAL, OPTICAL etc.) is set ( page 47 or 49 50).2 Press INPUT MODE to select “AUTO”.3 Press STANDARD to select “STANDARD”.4 Play a program source with the, mark. “ ” or “ ” lights, depending on the source.5 Press SURROUND PARAMETER.The surround back channel can be switched on and off using.6 Press set. D H to select the item, then press F G toCINEMA EQ.:Use this if movie dialogues sound harsh to lower the treble sound.Effective source / modeDolby Pro Logic IIx / Dolby Pro Logic / Dolby Digital / DTS Surround / DTS NEO:6 / WIDE SCREEND.COMP.:The dynamic range is compressed. Select one of 4 modes: “OFF”, “LOW”, “MID” (middle) or “HI” (high).Effective source / mode Dolby Digital /DTS (For DTS sources, only displayed for compatible software.)LFE:To play the various types of software properly, we recommend setting to the values shown below.

To play Dolby Digital software: “0 dB”. To play DTS movie software: “0 dB”. To play DTS music software: “–10 dB”. Basic OperationTONE:Adjust the tone control.Can be set in surround modes other than direct mode. Can be set separately for the different surround modes.

Basic OperationAFDM (Auto Flag Detect Mode):. ON:When software including Dolby Digital EX or DTS-ES 6.1- channel identification signals is played, 6.1-channel playback is performed automatically. The surround mode is set according to the program source being played. The “SB CH OUT” parameter on the surround parameters screen cannot be selected. OFF:Not detected automatically. The surround mode can be selected freely.Example: When playing Dolby Digital software (with EX flag) q When “AFDM” is “ON”, the “DOLBY DIGITAL + PL IIxCINEMA” mode is set automatically.w To play in the Dolby Digital EX mode, set “AFDM” to “OFF” and select “MTRX ON” at “SB CH OUT”.Example: qExample: wSome discs recorded in Dolby Digital EX do not include EX flag.

If the playing mode does not switch automatically when the AFDM turns “ON” during playback, manually set “SB CH OUT” to “PL IIx Cinema” or “MTRX ON”.7 Press ENTER or SURROUND PARAMETER.“Default Yes” and press F to reset all the settings.2 Dialog normalization functionThis operates automatically when playing Dolby Digital sources. This is a function for automatically correcting the standard signal level for different program sources.

The correction value can be checked by pressing.D i a l. N o r mO f f s e t - 4 d BThe numbers are the correction value when corrected to the standard level. Selecting the Dolby Pro Logic IIx (Pro Logic II) modeIt is possible to play analog input signals and digital input signals (2-channels) in the surround mode.This mode is optimal for playing program sources recorded in Dolby Surround.1 Press STANDARD to select “DOLBY PL IIx”.DOLBY PL IIx DTS NEO:62 Play a program source.3 Press SURROUND PARAMETER.4 Press F G to select the play mode.CINEMA:This mode is suited for playing movie sources recorded in Dolby Surround and general sources recorded in stereo.MUSIC:This mode is suited for playing stereo music signals in the surround mode. With music signals, the sound field expansion differs according to the type of music, the recording conditions (live/studio), etc. Because of this, the MUSIC mode offers a number of optional parameters for further adjusting the sound field.GAME:This mode is optimum for games.

The GAME mode can only be used for 2-channel audio sources.PL:This mode is compatible with conventional Dolby Pro Logic sources.Optional parameters can only be set in the MUSIC mode. Select “OPTIONS”, then press F.Press ENTER to return to the previous screen.

ENGLISHBasic Operation5 When “MUSIC” is selected:Press D H to select the item, then press F G to set.PANORAMA:This is effective when the surround effect seems weak.DIMENSION:This shifts the center of the sound field image to the front or surround side. This compensates for when the sound field image seems unbalanced. (0 to 6, default: 3)CENTER WIDTH:A natural expansion to the front can be achieved by adjusting the center signal’s output balance between the center and front channels. (0 to 7, default: 3)6 Press ENTER or SURROUND PARAMETER.345(When “MUSIC” is selected)h(When “OPTIONS” is selected). Selecting the DTS NEO:6 modeIt is possible to play analog input signals and digital input signals (2-channels) in the surround mode.1 Press STANDARD to select “DTS NEO:6”.DOLBY PL IIx DTS NEO:62 Play a program source.3 Press SURROUND PARAMETER.4 Press F G to select the play mode.CINEMA:This mode is optimum for playing movies. Decoding is performed with emphasis on separation performance to achieve the same atmosphere with 2-channel sources as with 6.1-channel sources.MUSIC:This mode is suited mainly for playing music.5 When “MUSIC” is selected:Press D H to select “CNTR.

IMAGE”, then press F G to set.CNTR. IMAGE:The expansion of the center channel can be adjusted. (0.0 to 1.0, default: 0.3)6 Press ENTER or SURROUND PARAMETER.3 5(When “MUSIC” is selected)28. When playing Dolby Digital, DTS, DVD-Audio and Super Audio CD.ENGLISHBasic OperationBasic OperationSurround modes and parametersSignals and adjustability in the different modesChannel outputParameter (default values are shown in parentheses)DolbyPRO LOGIC II/ IIx MUSIC MODENEO:6EXT. INSurround ModeSURROUNDMUSICFRONTSURROUNDSUB-D. COMPLFEAFDMSB CHTONEROOMEFFECTDigitalSUBWOOFERonlyonlyCENTERMODE onlyBACKCINEMA EQ.MODEDELAY TIMEL/RL/RL/RWOOFER.1.2.1OUTCONTROLSIZELEVELNIGHTON/OFFPANORAMADIMENSIONCENTERCENTERSW ATTmodeWIDTHIMAGEPURE DIRECT, DIRECTCEEEBC (OFF)C (0 dB)EEEEEEEC (OFF)ECEEEEEMULTI CH DIRECTCBBBBEC (0 dB)C (ON)CEEEEEEEEEEEEESTEREOCEEEBC (OFF)C (0 dB)EEC (0 dB)EEEEC (OFF)EEEEEEEEXT.

ENGLISHBasic OperationBasic OperationUsing the DENON original surround modesThe AVR-2807 is equipped with a high performance digital signal processor (DSP) that uses digital signal processing to recreate sound fields artificially. One of 10 surround modes can be selected according to the program source and parameters can be further adjusted to achieve even more realistic sound fields.Types of surround modes and their features7CH STEREOThis mode lets you enjoy stereo sound with 7 speakers. The front L (R) channel signals are played from thesurround and surround back L (R) channels and only the in-phase component of the L and R channels is(NOTE 1)played on the center channel.WIDE SCREENThis mode recreates the atmosphere of watching a movie in a theater with a large screen. Selecting the DSP surround simulation1 Press DSP SIMULATION.7CH STEREO WIDE SCREEN SUPER STADIUMVIRTUALROCK ARENAMATRIXJAZZ CLUBVIDEO GAMEMONO MOVIECLASSIC CONCERTThe 7CH STEREO mode can beselected directly bypressing.2 Press SURROUND PARAMETER.3 Press set.

D H to select the item, then press F G toEFFECT: (WIDE SCREEN mode only)Effect signals with the multi-surround speaker effects are played. When set to “OFF”, the SL/ SR channels are played from the SBL/ SBR channels, respectively.LEVEL: (WIDE SCREEN mode only)Adjust the strength of effect signals “1” to “15”.SB CH OUT. ON:Surround back channel played. OFF:Surround back channel not played.This operation can also be performed using.ROOM SIZE:Adjust the imaginary size of the recreated sound field space.

(Does not express size of room in which played.)There are 5 parameters: “small”, “med.s”, “medium”, “med.l” and “large”. Basic OperationUsing the fader functionWith this function, the volume of all the front side speakers or all the rear side speakers can be adjusted (attenuated) at once.1 Press CH SEL/ENTER.2 Press D H or CH SEL/ENTER to select “Fader”.3 Press F to attenuate the volume of all the front side speakers, G to attenuate the volume of all the rear side speakers.The fader function does not affect the subwoofer.It is possible to adjust so that the volume of the speaker whose volume is the lowest is –12 dB.23.

ENGLISHBasic OperationPreset memory1 Use the “Auto tuning” or “Manual tuning” operation to tune in the station to be preset in the memory.2 Press MEMORY.3 Press SHIFT to select the desired memory block (A to G).4 Press CHANNEL to select the desired preset channel (1 to 8).5 Press MEMORY again. Store the station in the preset memory.other channels, repeat steps 2 to 5.of 56 broadcast stations can be preset — 8 stations 1 to 8) in each of blocks A to G.memory block can also be selected by pressing SHIFT. User mode functionThe AVR-2807 is equipped with a function for storing the selected input source, the auto surround mode and input mode in the memory and selecting these settings when you want to use them.2 Storing the settings in the memory1 The following are stored in the memory: q Currently set input sourcew Currently set surround mode e Currently set input mode2 Press and hold USER MODE.Press and hold in until the selected user mode indicator lights.2 Calling the settings outPress USER MODE at which the settings you want to call out are stored. The selected user mode display lights. Advanced OperationPlaying the iPod ®The music recorded on the iPod can be played when using a DENON original Dock (ASD-1R). The iPod can be controlled using the buttons on the main unit and the remote control unit.iPod is a trademark of Apple Computer, Inc., registered in the U.S. And other countries.With the iPod, non-copyrighted contents and contents that may be legally reproduced or played may be reproduced and played by individuals for their personal use.

Violating copyrights is prohibited by law.1 Connect the AVR-2807 and iPod using the DENON original Dock ( page 20).2 Assign the input terminal at “Setting the iPod Assignment” ( page 47).3 Use FUNCTION to select the function assigned in step 2.(iPod screen)If the screens above are not displayed, the iPod may not be properly connected. Check the connections and settings.optional standard iPod Dock is DENON ASD-1R sold.NOTE:. DENON will accept no responsibility whatsoever for loss or damage of data on an iPod occurring when the iPod is used connected to the AVR-2807. Some of the functions may not operate, depending on the type of iPod and the software version.

ENGLISHAdvanced Operationn is pressed during playback, the front panel switches between the title name, artist name andname.on the iPod’s software version, it may not be to operate the iPod from the AVR-2807. Use the latest of the software. Information on the latest version of thecan be obtained on the Apple Computer website.do not want the on screen display to be displayed while the iPod, set “Function/Mode Status” at “Setting theScreen Display” to “OFF” (page 52).the AVR-2807 it is possible to display folder names and file on the screen like titles.

The AVR-2807 can display up to consisting of numbers, capital letters and small. ENGLISHAdvanced OperationMulti zone music entertainment system. When the outputs of the ZONE2 output terminals are wired and connected to power amplifiers installed in other rooms, different sources can be played in rooms other than the MAIN ZONE in which this unit and the playback devices are installed. Advanced OperationMulti-zone playback using the SPEAKER terminals2 When using the SURROUND BACK amplifier as the ZONE2 outputWhen the surround back’s power amplifier is assigned to the ZONE2 output channel at “Power Amp Assign” in the “System Setup Menu”, the surround back speaker terminals can be used as the ZONE2 speaker out terminals ( page 54).System configuration and connections example. Using this AVR-2807 internal amplifier as the ZONE2.MAIN ZONE 5.1-channel systemsZONE2MonitorMonitorFLFRFLFRCSWDVD playerAVR-2807ZONE2 Video outMulti-zone speaker outInputSLSR.

Denon Rc-1216 Manual

Description1. 100% New AV remote control2. Mini Order is 1 piece, there is no Batteries Included3. Packing detail:standard package with small carton for each pieceShippinging We ship to worldwide. Please see our shipping calculator to determine the shipping cost.Free shipping is standard shipping way, 10-30 days to get the goods.

If you are in hurry, please choose fast shippig way: DHL, UPSThe tracking number will be given on the intenet within 2 working days, so the buyer can trace the item online, the buyers are responsible for the customs tariffs.All shipping and handling fees are non-refundable.